Hyundai Genesis: Hands Free System / Hands Free Switch Repair procedures

Inspection
1.
Check for resistance between terminals in each switch position(LH).

[Audio]
Switch
Connector
terminal
Resistance
(±5%)
Speech Recognition
6~8
18.81k?
SEEK UP
6~8
4.51k?
SEEK DN
6~8
2.11k?
Mode
6~8
6.71k?
SEND
6~8
430?
END
6~8
1.11k?
MUTE
1~8
0
VOL UP
2~3
-
VOL DN
2~3
-

2.
Check for resistance between terminals in each switch position(RH).

[Cruise]
Switch
Connector
terminal
Resistance
(±5%)
CANCEL
2~3
180?
RES+
2~3
550?
SET-
2~3
330?
Cruise ON/OFF
2~3
880?
Space betweencars
2~3
2.54k?

Diagnosis With GDS
1.
In the body electrical system, failure can be quickly diagnosed by using the vehicle diagnostic system (GDS).
(1)
Self diagnosis : Checking failure and code number (DCT)
(2)
Current data : Checking the system input/output data state
(3)
Actuation test : Checking the system operation condition
(4)
Additional function : Controlling other features including system option setting and zero point adjustment
The BCM communicates with the GDS and then reads the input/output value and drives the actuator.
2.
Select the 'Steering wheel remote control' and the system to be checked in order to check the vehicle with the tester.
3.
Select the 'Steering wheel remote control (SWRC)' to check the Steering wheel remote control (SWRC)
   
Select 'Sensor Data' and 'Steering wheel remote control (SWRC)' to check the Instrument Panel Module (Sensor Data).
4.
Select the "Current date" menu to search the current state of the input/output data.
The input/output data for the sensors corresponding to the 'Premium AVN' can be checked.
Removal
1.
Disconnect the negative (-) battery terminal.
2.
Remove the driver airbag module.
(Refer to Restraint - "Driver Airbag (DAB) Module and Clock Spring")
3.
Loosening the screws from the steering cover.

4.
Remove the steering back cover (A)

5.
Loosen the screws after disconnecting the steering wheel remote control switch connector (A).

6.
Remove the handsfree remote control switch (A) after loosening the screws.

Installation
1.
Install the remote control switch on the steering wheel.
2.
Install the steering wheel.
3.
Reconnect the remote control switch connector and airbag connectors.
   
Make sure that the switch connector is plugged in properly.
4.
Install the driver airbag module.
5.
Connect the negative (-) battery terminal.
Hands Free Switch Schematic Diagrams
Circuit Diagram ...

Hands Free Mic Repair procedures
Inspection 1. Disconnect the negative (-) battery terminal. 2. Remove the overhead console. 3. Remove the handsfree mic (B) after disconnecting the handsfree mic connector (A). 4. Chec ...

Other information:

Hyundai Genesis (DH) 2013-2016 Service Manual: Relay Box (Passenger Compartment) Repair procedures


Fuse Inspection 1. Check that the fuse holders are loosely held and that the fuses are securely fixed by the holders. 2. Check that each fuse circuit has the exact fuse capacity. 3. Check the fuses for any damage.     If a fuse is to be replaced, be sure to use a new ...

Hyundai Genesis (DH) 2013-2016 Owners Manual: Resetting the driver's seat memory system


Take the following procedures to reset the driver's seat memory system, when it does not operate properly. To reset the driver's seat memory system 1. Press the Engine Start/Stop button to the ON position, set the gear in P (Park), and open the driver's door. 2. Operate the control ...

© 2013-2025 www.hgenesisdh.com